Etc Sensor3 CE (ESR3) Rack Bedienungsanleitung PDF herunterladen (Seite 3)

Table of Contents

Warnings. . . . . . . . . . . . . . . . . . . . . . . iii

Introduction . . . . . . . . . . . . . . . . . . . . . .1

How to use this Guide. . . . . . . . . . . . . . . . . . . . . . . . . . .1

Warning and Notice Conventions . . . . . . . . . . . . . . . . . .1

Contacting ETC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Prepare for Installation . . . . . . . . . . . . .3

Unpack and Inspect . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Main Circuit Breaker Protection . . . . . . . . . . . . . . . . . . .3

Energising the System . . . . . . . . . . . . . . . . . . . . . . . . . .3

Use 90°C Copper Wire . . . . . . . . . . . . . . . . . . . . . . . . . .3

Where to Mount the Rack . . . . . . . . . . . . . . . . . . . . . . . .4

Dimmer Room Requirements . . . . . . . . . . . . . . . . . . . . .4

Wire Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Installation of Racks . . . . . . . . . . . . . . .5

Mounting the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Mounting Racks on a Wall (ESR3-12 and ESR3-24) . . .5

Installing ESR3-36 and ESR3-48 Racks on the Floor . .6

Pedestal Mounting an ESR3-24 Rack . . . . . . . . . . . . . .6

Securing Sensor3 Racks to a Wall . . . . . . . . . . . . . . . . .7

Wall Mounting Racks Using Vibration Pads . . . . . . . . . .8

Floor Mounting Racks Using Vibration Pads . . . . . . . . .8

Securing Multiple Racks (Optional) . . . . . . . . . . . . . . .10

Rack Cabling Access . . . . . . . . . . . . . . . . . . . . . . . . . .11

Connect Line Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . .12

Preparing Line Feed Cable. . . . . . . . . . . . . . . . . . . . . .12

Land Load Wires. . . . . . . . . . . . . . . . .13

Land Load Wires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Cut Key Slots for Modules . . . . . . . . . . . . . . . . . . . . . . . . . .15

Cutting Key Slots for 25A and 50A Modules. . . . . . . . .15

Converting Neutral Disconnect Slots . . . . . . . . . . . . . .16

Installing Three-Slot Dimmer Lug Strips . . . . . . . . . . . .17

Control and Data Connections . . . . . .19

Dual and Single Backplane Differences . . . . . . . . . . . .19

Running DMX Cable to Racks. . . . . . . . . . . . . . . . . . . . . . .20

DMX Termination - Screw Terminals . . . . . . . . . . . . . .20

DMX Termination - IDC Connection . . . . . . . . . . . . . . .20

Setting DMX Termination . . . . . . . . . . . . . . . . . . . . . . .21

Running Ethernet to Racks . . . . . . . . . . . . . . . . . . . . . . . . .22

Ethernet with a NEFM. . . . . . . . . . . . . . . . . . . . . . . . . .22

Ethernet with an External Network . . . . . . . . . . . . . . . .22

1 2 3 4 5 6 7 8 ... 47 48

Keine Kommentare

Etc Sensor3 CE (ESR3) Rack Bedienungsanleitung Seite 3