ETC Source Four LED Series Bedienungsanleitung Seite 16
- Seite / 96
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
11 Source Four LED Profile v1.4.0 User Manual
Quick Setups (Daylight and Tungsten)
Step 1: On the Main Menu, scroll to Quick Setups.
Step 2: Press [Enter].
Step 3: Scroll to the desired setup and then press [Enter].
An asterisk (*) next to the setup name indicates that setup is active.
Step 4: Press [Enter] to return to the home screen.
The top line of the home screen displays the name of the active setup.
Studio Quick Setup
From the home screen (with no DMX), do any of the following.
• To adjust the Intensity, press [Up] or [Down].
The range is 0 to 100%.
• For the Lustr+ only, to adjust the White Point, press [Back] or [Enter].
The range is 2700 to 6500K.
• For the Lustr+ only, to adjust the Tint, press [Light bulb] & [Back] or [Enter].
[Back] increases magenta and [Enter] increases green.
• To return to the Main Menu, press [Home].
For advanced settings, refer to the next procedure.
Advanced Settings
Step 1: From the Main Menu press [Up] or [Down] to select Advanced Settings.
Step 2: Press [Enter].
Step 3: Access the individual settings via additional menus.
Step 4: Press [Enter] to return to the home screen.
Once you are familiar with your Source Four LED series fixture, you may alter any of the
numerous individual settings from the Advanced Settings menu. For more information, see
Advanced Menu, page 47.
Quick Setup Description
Control
Channels
Features
Studio
Video or film:
The default setting for Daylight and
Tungsten fixtures.Studio Quick Setup
enables stand-alone operation from the
User Interface on the back of the fixture if
no console is present. For more
information, see Studio Settings, page 73.
3 –
Intensity,
Strobe, Fan
Control
• Linear dimming curve
• Regulated output for brightness
consistency
• Strobe enabled
Stage
Theatrical lighting:
Behaves like a theatrical fixture in control
and dimming performance.
3 –
Intensity,
Strobe, Fan
Control
• Incandescent dimming curve
• Regulated output for brightness
consistency
• Strobe enabled
Single
Channel
Architectural installations:
Most streamlined settings for applications
with limited control options.
1 – Intensity
• Standard dimming curve
• Regulated output for brightness
consistency
• Automatic fan control
- User Manual 1
- Table of Contents 3
- Introduction 6
- Daylight and Tungsten 7
- Fixture Components 8
- Introduction 4 9
- Applications 10
- Document Conventions 10
- WARNING: 11
- Contacts 12
- Quick Start 13
- Configure 14
- Soft Focus Diffuser 14
- Quick Setups Menu 15
- Studio Quick Setup 16
- Advanced Settings 16
- Overview 17
- Specifications 18
- Typical Power Consumption 19
- Note About LED Fixtures 19
- Hardware 21
- Install Lens Tube 22
- Aim Adjustments 23
- Focusing the Beam 24
- Shaping the Beam 24
- Accessory Slot 26
- CAUTION: 27
- Adjusting the Yoke Position 28
- Installation Clearances 29
- Safety Cable 31
- Fixture Weight 31
- Connections 33
- DMX Profile 34
- Color Mixes 35
- Color Matching 37
- Direct Control 38
- Fan Control 38
- Tungsten and Daylight 39
- Lustr+ and Studio HD 39
- Installing Accessories 40
- Basic Menu Navigation 41
- User Interface Overview 42
- 2 Basic Menu Navigation 38 43
- Keypad Lockout 43
- Lustr+ screen shown 44
- Display Title 45
- Input Settings 45
- DMX Address 45
- Menu Navigation 46
- Operation 47
- Home Screen Displays 48
- 3 Operation 44 49
- Main Menu 50
- Operation 46 51
- Advanced Menu 52
- Data Loss 54
- HLL-2Min 54
- HLL-4ever 54
- Using Plus Seven Control 55
- Regulated 56
- Protected 56
- Standard 57
- Incandescent 57
- Output Freq 59
- Red Shift 59
- 3 Operation 56 61
- Fade Time 62
- Delay Time 63
- [Enter]. To discard 63
- Edit (Daylight and Tungsten) 64
- Copy to Other Fixtures 64
- Save DMX as Preset 64
- Sequences 65
- Link Time 67
- Finishing the Sequence 68
- Master/Slave Operation 69
- Current DMX In 70
- Network Statistics 71
- Individual Control (Ind Cntl) 72
- Recalibrate Fixture 73
- About Fixture 73
- Backlight 74
- BLght time out 74
- Language 75
- Status Indicators 75
- Operation 72 77
- Studio Settings 78
- 3 Operation 74 79
- Studio DMX Control 80
- Error Messages 81
- Software Updates 82
- Routine Maintenance 83
- Appendix A 86
- Menu Flow Chart 86
- System OK 87
- Menu Flow Chart 84 89
- To Sequences 90
- Status: Active 92
- To Recalibrate 93
- To Te s t 93
- Menu Flow Chart 90 95
Verwandte Produkte und Handbücher für Flutlichter ETC Source Four LED Series
(8 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern