ETC
®
Setup Guide
DIN Rail Enclosure Installation Kit
.cnI ,slortnoC ertaehT cinortcelE1 fo 1 egaPtiK noitallatsnI erusolcnE liaR NID
Corporate Headquarters
3031 Pleasant View Road, P.O. Box 620979, Middleton, Wisconsin 53562-0979 USA
Tel +608 831 4116
Fax +608 836 1736
London, UK
Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK
Tel +44 (0)20 8896 1000
Fax +44 (0)20 8896 2000
Rome, IT
Via Pieve Torina, 48, 00156 Rome, Italy
Tel +39 (06) 32 111 683
Fax +44 (0) 20 8752 8486
Holzkirchen, DE
Ohmstrasse 3, 83607 Holzkirchen, Germany
Tel +49 (80 24) 47 00-0
Fax +49 (80 24) 47 00-3 00
Hong Kong
Rm 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong
Tel +852 2799 1220
Fax +852 2799 9325
Service:
(Americas) service@etcconnect.com
(UK) service@etceurope.com
(DE) techserv-hoki@etcconnect.com
(Asia) service@etcasia.com
Web:
www.etcconnect.com
Copyright © 2010 ETC. All Rights Reserved.
Product information and specifications subject to change.
7180M2250
Rev B
Released 2010-12
ETC intends this document to be provided in its entirety.
Overview
This document covers the use of a DIN Rail Enclosure Installation Kit (ETC Part# 7180A1004)
which includes:
• Rugged 14”x14” junction box
• Ground bus bar
• Three one-foot pieces of 18GA wire (red, black & green)
Installation
It is recommended that you remove any electronics before drilling holes in the enclosure. Remove
any metal shavings from the enclosure before installing electronics and connecting power.
Step 1: Use the angle iron on
both ends of the box to
securely mount the box to a
rigid location.
Step 2: Mount the DIN rail
products on the provided DIN
rail. If you are using Power
over Ethernet (PoE IEEE
802.3af) to power the Mosaic
Show Controller,
skip steps 3 -
6 and reference the note
below.
Step 3: Land the mains power
on the DC power supply and
connect the incoming Ground
wire to the bus bar.
Step 4: Connect the power
supply to the ground bus bar.
Step 5: Connect the dc power
supply to the Mosaic Controller
(or other device) using the wire
supplied as follows:
• DC Pos.(+) = red
• DC Neg.(-)( ) = black
• Chassis( ) = green
Step 6: Finish installation as
specified in the installation
manual provided with the DIN
mounted products.
Note:
Optional 48V Power Supply kit (7180A1300) is available as needed to power the
Mosaic Show Controller and accessories.
Note:
If using PoE, the device must be grounded. Connect the supplied ground wire
(green/yellow) to the product or DIN rail grounding clamp.
Optional 48V
Power Supply kit
7180A1300
1
1
3
4
5
(2 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern